Code-3 LED PriZm II Perimeter Lights User Manual download pdf (Page 2)

The use of this or any warning device does not insure that all drivers can or will observe or react to an emergency

warning signal. Never take the right-of-way for granted. It is your responsibility to be sure you can proceed safely

beforeenteringanintersection,drivingagainsttrafc,respondingatahighrateofspeed,orwalkingonoraround

trafclanes.

The effectiveness of this warning device is highly dependent upon correct mounting and wiring. Read and follow

the manufacturer’s instructions before installing or using this device. The vehicle operator should insure daily that

all features of the device operate correctly. In use, the vehicle operator should insure the projection of the warning

signal is not blocked by vehicle components (i.e. open trunks or compartment doors), people, vehicles, or other

obstructions.

This equipment is intended for use by authorized personnel only. It is the user’s responsibility to understand and

obey all laws regarding emergency warning devices. The user should check all applicable city, state and federal

laws and regulations.

Public Safety Equipment, Inc., assumes no liability for any loss resulting from the use of this warning device.

Proper installation is vital to the performance of this warning device and the safe operation of the emergency vehicle.

It is important to recognize that the operator of the emergency vehicle is under psychological and physiological

stress caused by the emergency situation. The warning device should be installed in such a manner as to: A) Not

reduce the output performance of the system; B) Place the controls within convenient reach of the operator so that

he can operate the system without losing eye contact with the roadway.

Emergency warning devices often require high electrical voltages and/or currents. Properly protect and use caution

around live electrical connections. Grounding or shorting of electrical connections can cause high current arcing,

whichcancausepersonalinjuryand/orseverevehicledamage,includingre.Wait10minutesafterturningoff

the power from system before touching any internal components. Always wear hand and eye protection when

handling electrical components.

PROPER INSTALLATION COMBINED WITH OPERATOR TRAINING IN THE PROPER USE OF EMERGENCY

WARNING DEVICES IS ESSENTIAL TO INSURE THE SAFETY OF EMERGENCY PERSONNEL AND THE

PUBLIC.

WARNING

Unpacking & Pre-Installation

Carefully remove the light head from its protective packaging. Inspect the unit for transit damage. Report any

damage to the carrier and keep the shipping carton. Verify the contents of the package (refer to Table 3 and Fig-

ures2and3).Testthelightsbeforeinstallation.Totest,touchtheblackwiretogroundandtheredwireto12VDC.

If a problem occurs, contact the factory.

General Description

The PriZm II Perimeter lights are offered in sizes 3x7, 4x6 and 7x9. Both solid and multi-color are available.

Multi-color lights are “split” horizontally (left/right). The outer lens will be eld replaceable, and will provide a

waterproof barrier via an interface with a eld replaceable outer gasket. The units are surface-mounted, requir-

ing no recesses to be cut in the vehicles for normal mounting. Only a hole for wiring and small holes for mount-

ing screws will be required. The unit will be available with or without bezel, and they operate on 2 volts. The

solid color lights are offered in the following colors: Red, Blue, Amber, White and Green. Multi-colored light are

available in numerous congurations (refer to Table 3). Many ash patterns are offered, all between 75-150

fpm. The units also feature dimming, synchronization and independent on/off (certain models only).

Specications

3x7 4x6 7x9

Size 1.5”x4.75”x9.0”(w/bezel) 1.5”x6.0”x8.5”(w/bezel) 1.5”x9.0”x11.0”(w/bezel)

Weight 1.0lbs 1.1lbs 2.25lbs

Operating Voltage 11-15Volts

Average Current Draw

0.6(8LEDs),0.7(12LEDs) 1.6(24LEDs),1.9(36LEDs)

Peak Current Draw

1.3(8LEDs),1.6(12LEDs) 3.8 (24 LEDs), 4.6 (36 LEDs)

Note 1: At 12.8V, 78

F and using NFPA Quad Flash

Note 2: At 12.8V, 78

1 2 3 4 5 6 7 8

Comments to this Manuals

No comments

Code-3 LED PriZm II Perimeter Lights User Manual Page 2

Comments to this Manuals

Related products and manuals for Lighting Code-3 LED PriZm II Perimeter Lights